wombat.ch

your Partner for Network Design and CMS

Hardware Information

Hardware Information

Network bonding types

| Written by vincent | Print | Email | Hits: 101081

Network bonding types

 

active-backup Active-backup policy: Only one slave in the bond is active. A different slave becomes active if, and only if, the active slave fails. The bond's MAC address is externally visible on only one port (network adapter) to avoid confusing the switch. This mode provides fault tolerance. The primary option affects the behavior of this mode.
balance-xor XOR policy: Transmit based on [(source MAC address XOR'd with destination MAC address) modulo slave count]. This selects the same slave for each destination MAC address. This mode provides load balancing and fault tolerance.
broadcast Broadcast policy: transmits everything on all slave interfaces. This mode provides fault tolerance.
802.3ad

IEEE 802.3ad Dynamic link aggregation. Creates aggregation groups that share the same speed and duplex settings. Utilizes all slaves in the active aggregator according to the 802.3ad specification.


Pre-requisites:
Ethtool support in the base drivers for retrieving the speed and duplex of each slave.
A switch that supports IEEE 802.3ad Dynamic link aggregation.
Most switches will require some type of configuration to enable 802.3ad mode.
balance-tlb

Adaptive transmit load balancing: channel bonding that does not require any special switch support. The outgoing traffic is distributed according to the current load (computed relative to the speed) on each slave. Incoming traffic is received by the current slave. If the receiving slave fails, another slave takes over the MAC address of the failed receiving slave.


Prerequisite:
Ethtool support in the base drivers for retrieving the speed of each slave.
balance-alb Adaptive load balancing: includes balance-tlb plus receive load balancing (rlb) for IPV4 traffic, and does not require any special switch support. The receive load balancing is achieved by ARP negotiation. The bonding driver intercepts the ARP Replies sent by the local system on their way out and overwrites the source hardware address with the unique hardware address of one of the slaves in the bond such that different peers use different hardware addresses for the server.

Source:

Internet but can't find it any more

 

Add a comment
Category: Hardware Information

PoE-Splitter TL-POE10R

| Written by vincent | Print | Email | Hits: 104591

TL-POE10R 4.0-P1 transpProduktfunktionalitäten

Der PoE-Splitter TL-POE10R ist voll kompatibel zum IEEE802.3af-Standard und kann mit allen IEEE802.3af-PoE-kompatiblen PSEs (Power Source Equipments) oder PoE-Supplier-Adaptern wie dem TL-SF1008P oder TL-POE150S von TP-LINK oder mit anderen, gleichwertigen Produkten verwendet werden, um 12V, 9V oder 5V Gleichspannung dorthin zu liefern, wo es keine Stromleitung oder Steckdosen gibt, und wo Sie Geräte wie APs, IP-Kameras oder IP-Telefone einsetzen wollen.

Add a comment

Read more: PoE-Splitter TL-POE10R

Category: Hardware Information

Cisco RV016 Multi-WAN VPN Router

| Written by vincent | Print | Email | Hits: 113275

cisco rv0161Cisco RV016 Multi-WAN VPN Router

 

 

 

Basic Question, how to reset a Cisco RV016?

 

 

Basic Question, how to access a resetet/new RV016

Connect only the PC to the Switch / no connection to a router
Reboot your Computer with DHCP enabled

http://192.168.1.1


admin an admin to access

Add a comment
Category: Hardware Information

adaptec 6405E - Wo muß das graue Sideband - Kabel angeschlossen werden?

| Written by vincent | Print | Email | Hits: 115751

Wo muß das graue Sideband - Kabel angeschlossen werden?


Das interne Adaptec mini-SAS x4 to (4x) SATA Fanout Kabel verfügt über ein zusätzliches graues 8-poliges Kabel mit 10-poligem Stecker. Wo wird dieses Kabel angeschlossen?

Add a comment

Read more: adaptec 6405E - Wo muß das graue Sideband - Kabel angeschlossen werden?

Category: Hardware Information

Subcategories

Router Article Count:  19

Turris Omnia Article Count:  14

Switch Article Count:  1

NAS / SAN Article Count:  4

Gadgets Article Count:  33

Gadget (englisch für Apparat, technische Spielerei oder auch Schnickschnack) bezeichnet ein technisches Werkzeug oder Gerät mit bisher so nicht bekannter Funktionalität und/oder besonderem Design. Es ist traditionellerweise klein und handlich und zum Mitführen konzipiert. Eine große Rolle spielt der Spaßfaktor eines Gadgets: Geräte, die sich als Gadget definieren, sind oft Grenzgänger zwischen sinnvoller Funktionalität und Verspieltheit.Der Duden definiert Gadget als „kleiner, raffinierter technischer Gegenstand“.

DCIM Article Count:  10

Data Center Infrastructure Management

iot Article Count:  117

Singelboard Artikel Article Count:  6

Raspberry Pi Board Article Count:  11

Arduino Article Count:  3

Sensor & Aktor Article Count:  4

Projects Article Count:  14

Digi-Bee Article Count:  4

parts list Article Count:  5

ZigBee Article Count:  6

Passiv Parts List Article Count:  2

433MHz Remote Sensor Article Count:  2

Solar Power | Batterie (Battery) Article Count:  7

last modified

Related Articles

Perfect Server

neusten Nachrichten

Hardware

lamp

RSS Feed


Warning: Invalid argument supplied for foreach() in /var/www/clients/client2/web2/web/j/modules/mod_jw_srfr/helper.php on line 39

Warning: Invalid argument supplied for foreach() in /var/www/clients/client2/web2/web/j/modules/mod_jw_srfr/helper.php on line 39

neusten Links


Warning: count(): Parameter must be an array or an object that implements Countable in /var/www/clients/client2/web2/web/j/modules/mod_quicklistweblinks/helper.php on line 78
many More Links »

part of ...

Schweizer Informatik Gesellschaft SI
Linux Counter
FairPhone
APS Standard
Internet Society
Linux Counter

Disqus

 

Learning Network

Cisco Learning Network
Linux Professional Institute (LPI)

Seti@home & Boinc

myBonic

statistik

 

Who is Online

We have 383 guests and no members online

We have 380 guests, no bots and no members online

Designed by Vincent Kocher.