wombat.ch

https your homepage with - letsencrypt

- Let’s Encrypt

- sjau - Let's Encrypt 2 ISPConfig

- simplylinux.ch

-

-

-

-

-

-

-

 Storage Unit for Proxmox with FreeNas

Inspired by Bernardo's Tech Blog

so wünsche ich mir die NAT funktionalität

Ziel: diverse Private IP Adressen durch eine Singel Public IP Adresse zu erreichen.
Singel Public IP
Multi Container
Multi Domaine
Multi Subdomaine

======

Vorschläge für eine saubere Installation .....

• -

Proxmox openVZ
Ubuntu 14.04 / 175GB / 4GB
The Perfect Server – Ubuntu 14.04 (Apache2, BIND, Dovecot, ISPConfig 3)

punkt 10
service apparmor stop
gibt es nicht

Punkt 12
service sendmail stop
gibt es nicht

punkt16:

OpenVSwitch Installation in a Proxmox Installation

1. install openvswitch - important: /etc/apt/sources.list must contain "deb http://download.proxmox.com/debian wheezy pvetest"

2. apt-get install openvswitch-switch

Following steps by WEB-GUI:

3. If you continue using existing physical NICs at host and IP address: remove IP-address and ports from vmbr0

4. create an ovs bridge e.g. vmbr1(no ports for the moment) and assign the desired IP address, probably 192.168.1.12, activate autostart too

5. create an ovs bond with slaves eth0 eth1 (I suppose) and select as bridge vmbr1

6. assign the virtual NICs in the VMs to vmbr1

7. reboot

You can verify after reboot the proper configuration by
Code:   ovs-vsctl show
should show your configuration (bridge, ports), version must be 2.0.90 or higher

Quelle:    forum.proxmox.com

my wish with Proxmox would be:
Have some virtuell Server KVM and OpenVZ and reach them with IPv6
The Proxmox Host (Server) itself dont't need IPv6, he will only be reached in a local Network with a Privat IPv4

the Question was/is how to do it:

So what nedd to be configured on the Proxmox Server?

And what need to be configured on the KVM and the openVZ Server?

I have the following Hardware and would like to use Proxmox for virtualisation.

I have 2 Nic Port Eth0 and Eth1
i have a Cisco-Switch and Fritzbox as Switch and Router

the Cisco-Switch is also conected to the router

Router  -------------- Server
Router  --- Switch --- Server

i would like
to bundle Eth0 and Eth1 to share bandwith
as i found out it would be a Bond (what is the difference between OVS Bond and Linux Bond?)

I would like
to use IPv6 Adresse for this Container which should be reached bei outside.

Download a ISO file burn a CD, a USB Stick what work for the installation he is asking for cd and the Installation will hang....

At a point you will be asked to give a
Servername, IP, Subnetmask, Gateway, Domaine, Password ...

After a reboot you can start with https://yourIP:8006 (Example you have to use your one defined IP Adresse)

and Login with root and your password

i have done a Linux Bond0 LACP Mode and after a reboot which i had to do, i could not conect any more. Why?
and what is the difference:

Linux Bond Mode
- balance-rr
- active-backup
- balance-xor
- broadcast
- LACP (802-3ad)
- balance-tlb
- balance -alb

and what is a Slaves:?

Install Adaptec 6405E and Monitor with Munin
doch vorher adaptec 6405E - Wo muß das graue Sideband - Kabel angeschlossen werden

Install APC UPS Pro 900 and Monitor with Munin

my Setup
Verbinden des APC UPS Pro 900 mit dem Linux Server (Debian 7.5 wheezy)
APC UPS Pro 900 hat einen RJ45/Seriellen Port
Server auf ein USB Port

Check it mit

dann noch mehr Infos

es kommen noch mehr Infos ... sind aber nicht relevant wir wissen das eine kommunikation stattfindet

Dann muss die Datei apcupsd.conf angepasst werden

dabei sind die 3 Punkte wichtig:
UPSName deineUSVname
UPSCable usb
UPSTYPE usb

anpassen von ISCONFIGURED von no auf yes wechseln

und weitere Infos....

=================== ====

APC UPS Status mit Munin überwachen

Munin-node ist bereits installiert und läuft

no you could be changeing the name of the UPS .....

more Information Links:
apcupsd - Debian Wiki
apcupsd - Community Help Wiki
Official website